Mastering Basic Plumbing for Installing a Bathtub
Mastering Basic Plumbing for Installing a Bathtub
Blog Article
Are you currently on the lookout for selective information about How to Install a Bathtub?
:max_bytes(150000):strip_icc()/adhesive-type-tub-and-shower-surround-2718959-hero-22d394dc48de474a988eeaad88e9d7b0.jpg)
Mounting a bath tub isn't precisely rocket science, but it does call for strong plumbing, carpentry, and also occasionally, tiling skills. Changing an old tub with a new one is additionally a moderately hard job. If the old bathtub is easily available, the task can move easily; if you have to open up a wall surface to eliminate the old bathtub and also position the brand-new bath tub, the task is much harder. In either situation, the task is within a home handyman's skills, although you will require an assistant to move out the old bathtub and also embeded in the brand-new one. Make certain you have actually qualified yourself for the job and also are comfortable attempting it. As opposed to hiring a specialist to take over a halfway-completed job, it is far better to take into consideration using one prior to you begin. Possibilities are you may require a specialist plumber to make tube links.
This short article will aid you set up a new bath tub in your shower room if you have currently gotten a new bathtub and do not need to transform the plan of your previous water supply pipelines.
Your tools as well as material checklist need to make up the following:
Removing Old Taps
If you require to change old faucets with new ones as a part of your installation, then the first thing you need to do is separate the supply of water. After doing so, switch on the faucets to drain any type of water continuing to be in the system. The procedure of removing the existing taps can be fairly bothersome because of the restricted gain access to that is commonly the instance.
Utilize a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that links the supply pipelines to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. Once the supply pipes have been eliminated, make use of the very same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning during this process. Once the faucets have actually been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any old sealing substance.
Prior to carrying on to fit the new taps, contrast the pipe connections on the old faucets to the new faucets. If the old faucets are longer than the new faucets, after that a shank adapter is required for the new faucets to fit.
Suitable New Touches
If the tails of the brand-new taps are plastic, then you will need a plastic connector to avoid damage to the string. One end of the adapter fits on the plastic tail of the tap as well as the other end provides a link to the existent supply pipelines.
If you require to fit a monobloc, then you will certainly require minimizing couplers, which connects the 10mm pipe of the monobloc to the standard 15mm supply pipe.
Next off, place the faucet in the mounting hole in the bath/basin making certain that the washers are in place between the tap as well as the sink. Safeguard the faucet in position with the producer supplied backnut. As soon as the tap is safely in position, the supply pipes can be linked to the tails of the faucets. The faucets can either be connected by utilizing corrugated copper piping or with regular faucet adapters. The former type must be linked to the tap ends first, tightening just by hand. The supply pipelines can later be connected to the other end. Tighten up both ends with a spanner after both ends have actually been linked.
Setting up the Bathtub
Using the two wooden boards under its feet, put the tub in the needed position. The wooden boards are helpful in uniformly spreading out the weight of the bathtub over the area of the boards rather than concentrating all the weight onto 4 tiny points.
The following objective is to make sure that the bath tub is leveled all round. This can be achieved by examining the level and adjusting the feet on the tub up until the level reviews degree.
To mount faucets, fit all-time low of the outermost flexible faucet adapter to the appropriate supply pipe by making a compression join; then do the very same for the various other faucet.
Switch on the water system as well as inspect all joints and brand-new pipework for leakages as well as tighten them if required. Fill the bathtub as well as likewise check the overflow electrical outlet and also the typical electrical outlet for leakages.
Finally, deal with the bathroom paneling as explained in the manufacturer's user's manual. Tiling and securing around the bathtub must wait up until the bathtub has actually been used at least when as this will certainly settle it into its final position.
Preparing for the Installment
To start with, the supporting frame provided with the bath needs to be fitted (if required) according to the producer's directions. Next off, fit the faucets or mixer to the bath tub. When suitable the faucet block, it is essential to make certain that if the faucet includes a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to prevent strain on the bath tub.
Fit the versatile tap connectors to the bottom of both taps using 2 nuts and also olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and then pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Examine the plug-hole outlet for an inlet on the side for the overflow pipeline.
Next, fit the end of the adaptable overflow pipe to the overflow outlet. Afterwards, screw the pipeline to the overflow face which need to be fitted inside the bath. Make certain you make use of all of the provided washers.
Link the catch to the bottom of the waste outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and screw on the trap to the electrical outlet. Connect the bottom of the overflow tube in a comparable manner.The bathroom should currently prepare to be suited its last setting.
Tiling Around the Tub
In the area where the bath meets the floor tile, it is essential to secure the joins with a silicone rubber caulking. This is very important as the fitting can move sufficient to break a rigid seal, creating the water to pass through the wall in between the bath and the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can select from a variety of coloured sealants to assimilate your fixtures as well as installations. They are sold in tubes and also cartridges, and are capable of securing voids up to a width of 3mm (1/8 inch). If you have a bigger void to fill, you can fill it with twists of drenched paper or soft rope. Bear in mind to always fill the bathtub with water before sealing, to permit the movement experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into account this motion prior to sealing.
Conversely, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as cut to size, are also easily readily available on the marketplace. It is a good idea to fit the tiles making use of water-resistant or waterproof glue and cement.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
As an enthusiastic reader on How to Install a Bathtub Yourself, I thought sharing that blog post was sensible. Kindly take a moment to distribute this write-up if you appreciated it. Thank you for going through it.
Reliable plumber? Dial! Report this page